Changes 1 GOST 7512 82. Examples of abbreviated recording of defects when deciphering images and documenting the results of radiographic testing

Annex 1 (recommended). Thickness of metal intensifying screens and methods of loading film into cassettes using screens Appendix 2 (informative). Thickness of protective lead screens Appendix 3 (mandatory). Markings for sensitivity standards and marking of groove standards Appendix 5 (mandatory). Conditional recording of defects in the interpretation of images and documentation of the results of radiographic testing Appendix 6 (reference). Examples of abbreviated recording of defects when deciphering images and documenting the results of radiographic testing

Interstate standard GOST 7512-82
"Non-destructive testing. Welded joints. Radiographic method"
(approved by the Decree of the State Standard of the USSR of December 20, 1982 N 4923)

non-destructive testing. Welded joints. Radiography method

Instead of GOST 7512-75

This standard specifies a method for radiographic testing of welded joints made of metals and their alloys, made by fusion welding, with a thickness of the welded elements from 1 to 400 mm, using x-ray, gamma and bremsstrahlung radiation and radiographic film.

1. General Provisions

1.1. Radiographic control is used to detect cracks, lack of penetration, pores, slag, tungsten, oxide and other inclusions in welded joints.

1.2. Radiographic control is also used to detect burns, undercuts, assess the magnitude of the convexity and concavity of the root of the seam, which are unacceptable for external examination.

1.3. Radiographic control does not reveal:

Any discontinuities and inclusions with a size in the direction of transmission less than twice the sensitivity of the control;

Lack of penetration and cracks, the opening plane of which does not coincide with the direction of translucence and (or) the opening value is less than the values \u200b\u200bgiven in Table. one;

Any discontinuities and inclusions, if their images on the pictures coincide with the images of foreign parts, sharp corners or sharp changes in the cracks of the translucent metal.

1.1-1.3.

Table 1

1.4. Welded joints with a ratio of the radiation thickness of the deposited weld metal to the total radiation thickness of at least 0.2 are subjected to radiographic control, having bilateral access, which makes it possible to install a cassette with a radiographic film and a radiation source in accordance with the requirements of this standard.

(Introduced additionally, Rev. N 1).

2. Requirements for control accessories

2.1. For radiographic inspection, marks should be used that are made of a material that ensures that they are clearly visible on radiographic images.

Markings of sizes established by GOST 15843 should be used.

2.2. During radiographic control, radiographic films that meet the requirements of the technical specifications for them should be used.

The type of radiographic film must be established by the technical documentation for the control or acceptance of welded joints.

2.3. During radiographic control, radiation sources provided for by GOST 20426 should be used.

The type of radioactive source, the voltage on the X-ray tube and the energy of accelerated electrons must be established depending on the thickness of the material being scanned by the technical documentation for the control or acceptance of welded joints.

2.4. Metal and fluorescent screens should be used as intensifying screens for radiographic testing.

The type of intensifying screen must be established by the technical documentation for the control or acceptance of welded joints.

The thickness of metal intensifying screens and methods for loading film into cassettes using screens are given in Appendix 1.

2.5. Screens must have a clean, smooth surface. The presence of wrinkles, scratches, cracks, tears and other defects on the screens is not allowed.

2.6. Film loading cassettes must be opaque and provide a tight hold of the intensifying screens to the film.

2.7. To protect the film from scattered radiation, it is recommended to shield the film cassette from the side opposite to the radiation source with lead screens.

The thickness of the protective screens is given in Appendix 2.

2.8. To determine the sensitivity of the control, wire, groove or plate sensitivity standards should be used.

2.9. Sensitivity standards should be made of a metal or alloy whose base is similar in chemical composition to the base of the welded joint being tested.

2.10. The shape and dimensions of the wire sensitivity standards are shown in Fig. 1 and in table. 2. The length of the wires in the standards is (20+-0.5) mm. Limit deviations for wire diameters:

Up to 0.2 mm... +-0.01 mm St. 0.2" 1.6mm...+-0.03mm" 1.6" 4.0mm...+-0.04mm.

table 2

Number standard	d_1	d_2	d_3	d_4	d_5	d_6	d_7	h
1	0,2	0,16	0,125	0,10	0,08	0,063	0,05	1,2

Limit deviations of other sizes - +-0.5 mm.

The insert and case for wire standards should be made of flexible transparent plastic.

(Changed edition, Rev. N 1).

2.11. The shape and dimensions of the groove sensitivity standards are shown in Fig. 2 and in table. 3.

Table 3

Number this- womb	Groove depth						Previous off deep bins cana- wok	R, not more	a		b		With		h		L
Number this- womb	h_1	h_2	h_3	h_4	h_5	h_6	Previous off deep bins cana- wok	R, not more	But- min.	Prev off	But- min.	Previous off	But- min.	Previous off	But- min.	Previous off	But- min.	Previous off
1	0,60	0,5	0,40	0,3	0,20	0,10	-0,05	0,1	2,5	+-0,30; +-0,150	0,5	+0,2; +0,1	10	-0,360	2	-0,100	30	-0,52
2	1,75	1,5	1,25	1,0	0,75	0,50	-0,10	0,2	4,0	+-0,40	1,5	+0,3	12	-0,430	4	-0,120	45	-0,62
3	-	-	3,00	2,5	2,00	1,50	-0,25	0,3	6,0	+-0,40	3,0	+0,3	14	-0,430	6	-0,120	60	-0,74
3	4,00	3,5	-	-	-	-	-0,30	0,3	6,0	+-0,40	3,0	+0,3	14	-0,430	6	-0,120	60	-0,74

2.12. The shape and dimensions of the plate sensitivity standards are shown in Fig. 3 and in table. four.

Table 4

Number standard	h		D		d		a		b		With		L
	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off
1	0,1		0,2		0,1		5		5		10		25

2 3 4 5	0,2 0,3 0,4 0,5	-0,02 5	0,4 0,6 0,8 1,0	+0,025	0,2 0,3 0,4 0,5	+0,025
6 7 8 9	0,60 0,75 1,00 1,25		1,2 1,5 2,0 2,5		0,60 0,75 1,00 1,25		6		7		12		35

10 11 12	1,5 2,0 2,5	-0,1	3,0 4,0 5,0	+0,10 +0,12 +0,12	1,5 2,0 2,5	+0,1	7	+-0,18	9		14		45

2.13. Marking of sensitivity standards should be carried out with lead numbers in accordance with GOST 15843 in accordance with Appendix 3. The first digit of the marking should indicate the material of the standard, the next (one or two digits) - the number of the standard.

Symbols for the material of the sensitivity standard: for alloys based on iron - 1, aluminum and magnesium - 2, titanium - 3, copper - 4, nickel - 5.

2.14. For marking groove standards, it is allowed to use cutouts and holes or only holes specified in Appendix 3. In this case, the thickness of the standard at the place of marking should be equal to h.

When marking standards with holes, the length of standard N 1 is 27_ (-0.52) mm, N 2 - 38.5 (-0.62) mm, N 3 - 53 (0.74) mm.

2.15. For welded products intended for export, it is allowed to use other types of sensitivity standards, if it is provided for by the export conditions.

3. Preparation for control

3.1. Radiographic control should be carried out after removing external defects found during external examination of the welded joint and cleaning it from bumps, slag, metal splashes, scale and other contaminants, the images of which in the image may interfere with the interpretation of the image.

3.2. After stripping the welded joint and eliminating external defects, the welded joint should be marked into sections and marked (numbered) of the sections.

3.1, 3.2. (Changed edition, Rev. N 1).

3.3. The system for marking and marking sections is established by technical documentation for the control or acceptance of welded joints.

3.4. During the control, sensitivity standards and markings should be installed at each site.

3.5. Sensitivity standards should be installed on the controlled area from the side facing the radiation source.

3.6. Wire standards should be installed directly on the seam with the direction of the wires across the seam.

3.7. Groove standards should be installed at a distance of at least 5 mm from the seam with the direction of the grooves across the seam.

3.8. Plate standards should be installed along the seam at a distance of at least 5 mm from it or directly on the seam with the direction of the standard across the seam so that the images of the marking marks of the standard do not overlap with the image of the seam in the picture.

3.9. When inspecting the circumferential welds of pipelines with a diameter of less than 100 mm, it is allowed to install groove standards at a distance of at least 5 mm from the weld with the grooves directed along the weld.

3.10. If it is impossible to install standards from the side of the radiation source when testing welded joints of cylindrical, spherical and other hollow products through two walls with deciphering only the area of the welded joint adjacent to the film, as well as during panoramic transillumination, it is allowed to install sensitivity standards from the side of the film cassette.

3.11. (Deleted, Rev. N 1).

3.12. Markings used to limit the length of sections of welded joints inspected in one exposure should be installed at the boundaries of the marked sections, as well as at the boundaries of the deposited and base metal when testing welded joints without reinforcement or with the weld reinforcement removed.

3.13. The markings used for numbering the controlled areas should be installed on the controlled area or directly on the film cassette so that the images of the markings in the pictures do not overlap with the image of the seam and the heat-affected zone according to clause 5.7.

3.14. If it is impossible to install sensitivity standards and (or) markings on the controlled area of the welded joint in accordance with the requirements of this standard, the procedure for testing without installing sensitivity standards and (or) markings should be provided in the technical documentation for the control or acceptance of welded joints.

(Changed edition, Rev. N 1).

4. Control scheme

4.2. With a limited width of the welded element, it is allowed to test tee welded joints with the direction of radiation along the generatrix of this element in accordance with Fig. 6.

4.2a. When testing circumferential welded joints of cylindrical and spherical hollow products, as a rule, it is necessary to use schemes of transillumination through one wall of the product (schemes of Fig. 5a, b, f, g, h). In this case, it is recommended to use transmission schemes with the location of the radiation source inside the controlled product:

5.1, 5.2. (Changed edition, Rev. N 1).

5.3. When inspecting welded joints according to fig. 5h (panoramic transillumination), the ratio of the inner diameter d to the outer diameter D of the controlled joint should not be less than 0.8, and the maximum size of the focal spot Ф of the radiation source should not be more than

5.4 In cases where the dimensions of defects are not determined (for example, defects are not allowed regardless of their size), the ratio between the inner and outer diameters of the controlled joint given in clause 5.3 may not be observed.

5.5. In the absence of a radiation source that meets the requirements of clause 5.3, it is allowed during control according to fig. 5h use radiation sources with a maximum focal spot size that satisfies the relation

In this case, the sensitivity standard should be installed on the weld or weld simulator used in determining the sensitivity, only on the side of the radiation source.

5.6. The length of the images should provide overlapping images of adjacent sections of welded joints with a length of the controlled section up to 100 mm, at least 0.2 of the length of the section, with a length of the controlled section over 100 mm - not less than 20 mm.

5.7 The width of the images should provide images of the weld, sensitivity standards, markings and heat-affected zones with a width of:

For butt and lap joints:

not less than 5 mm - with a thickness of welded edges up to 5 mm;

not less than the thickness of the edges to be welded - with the thickness of the edges to be welded St. 5 to 20 mm;

not less than 20 mm - with a thickness of welded edges of St. 20 mm;

For tee and corner joints - it is established by the technical documentation for the control or acceptance of these joints.

6. Transcription of pictures

6.1. Viewing and interpretation of images should be carried out after they have completely dried in a darkened room using special illuminators-negatoscopes.

Negatoscopes with adjustable brightness and illuminated field size should be used. The maximum brightness of the illuminated field should be at least 10(D+2) cd/m2, where D is the optical density of the image. The dimensions of the illuminated field should be adjusted using movable shutters or mask screens within such limits that the illuminated field is completely covered by the image.

(Changed edition, Rev. N 1).

6.2. Photographs approved for decoding must meet the following requirements:

The pictures should not have spots, stripes, pollution and damage to the emulsion layer, making it difficult to decipher them;

The photographs must show images of limit marks, markings and sensitivity standards;

The optical density of the images of the controlled section of the weld, the near-weld zone and the sensitivity standard must be at least 1.5;

The decrease in the optical density of the image of the welded joint in any part of this image in comparison with the optical density of the image of the sensitivity standard should not exceed 1.0.

6.3. The sensitivity of the control (the smallest diameter of the wire standard detected in the image, the smallest depth of the groove of the groove standard detected in the image, the smallest thickness of the plate standard, at which a hole with a diameter equal to twice the thickness of the standard is detected in the image), should not exceed the values given in Table. 6.

Table 6

Note. When using wire standards of sensitivity, values of 0.30; 0.60; 0.75 and 1.50 mm are replaced by 0.32; 0.63; 0.80 and 1.60 mm.

(Changed edition, Rev. N 1).

Specific sensitivity values should be established by the technical documentation (drawing requirements, specifications, control and acceptance rules) for the controlled products.

For nuclear power plants, sensitivity requirements are established by the relevant regulatory documents.

6.4 In accordance with the requirements of the technical documentation for controlled products, it is allowed to determine the sensitivity (k) as a percentage using the formula

6.5. Interpretation and evaluation of the quality of welded joints from images that do not have images of sensitivity standards is allowed:

With panoramic transillumination of circumferential welded joints with simultaneous exposure of more than four films. In these cases, regardless of the total number of shots, it is allowed to set one sensitivity standard for each quarter of the circumference of the welded joint;

When it is impossible to use sensitivity standards.

In these cases, the sensitivity is determined on the simulators of the welded joint during processing of control modes.

6.6. When deciphering the images, the dimensions of the images of cracks, lack of penetration, pores and inclusions are determined, and, if necessary, the magnitude of the concavity and convexity of the root of the weld is estimated (in cases where the root of the weld is not available for external examination).

The list of dimensions to be determined and the method for assessing the concavity and convexity of the weld root should be given in the technical documentation for the control and acceptance of welded joints.

6.7. When documenting the results of image interpretation, the sizes determined from the images should be rounded up to the nearest values from the range of 0.2; 0.3; 0.4; 0.5; 0.6; 0.8; 1.0; 1.2; 1.5; 2.0; 2.5; 3.0 mm or the nearest integer value in millimeters if the size determined from the image exceeds 3.0 mm.

6.8. If, during testing, the film is located at a distance H from the surface of the tested welded joint facing the film, and the relation

it is recommended to multiply the dimensions determined from the image before rounding them by the coefficient

6.6-6.8. (Changed edition, Rev. N 1).

6.9. When measuring the size of defects up to 1.5 mm, a measuring magnifier with a division value of 0.1 mm, St. 1.5 mm - any measuring device with a division value of 1 mm.

6.10. The results of interpretation of images and the sensitivity of the control must be recorded in the conclusion or logbook of the results of control, the form of which should be established by the technical documentation for the control or acceptance of welded joints.

6.11. To designate defects in the conclusion or log of control results, the symbols given in Appendix 5 should be used.

Examples of abbreviated recording of defects when deciphering images are given in Appendix 6.

7. Security requirements

7.1. The main hazards for personnel during radiographic control are exposure to the body of ionizing radiation and harmful gases formed in the air under the influence of radiation, and electric shock.

7.2. Radiographic control and recharging of radioactive sources should be carried out only with the use of equipment specially designed for these purposes and in good condition, the documentation for the manufacture and operation of which, if issued in more than three copies, must be agreed with the USSR State Committee for the Use of Atomic Energy and the Chief Sanitary - epidemiological department of the Ministry of Health of the USSR; up to three copies - with local bodies of the sanitary and epidemiological service.

7.3. The electrical equipment of existing stationary and portable installations for radiographic control must comply with the requirements of GOST 12.2.007.0 and the "Rules for Electrical Installations", approved by the Main Technical Directorate for the Operation of Energy Systems and the State Energy Supervision Authority of the USSR Ministry of Energy.

7.4. When carrying out radiographic control, storage and recharging of radioactive radiation sources, the safety of work must be ensured in accordance with the requirements of the "Basic Sanitary Rules for Working with Radioactive Substances and Other Sources of Ionizing Radiation" OSP-72/80 N 2120-80, approved by the Chief State Sanitary Doctor of the USSR January 18, 1980, "Radiation Safety Standards" NRB-76 N 141-76, approved by the USSR Chief State Sanitary Doctor June 7, 1976, "Sanitary Rules for Radioisotope Defectoscopy" N 1171-74, approved by the Deputy Chief State Sanitary Doctor of the USSR August 7, 1974 and GOST 23764.

7.5. When operating stationary and portable installations for radiographic control connected to an industrial power grid, the safety of work must be ensured in accordance with the requirements of the "Rules for the technical operation of consumer electrical installations" and the "Safety Rules for the operation of consumer electrical installations", approved by the State Energy Supervision Authority on April 12, 1969.

7.6. When transporting radioactive radiation sources, the requirements of the "Safety Rules for the Transportation of Radioactive Substances" PBTRV-73 N 1139-73, approved by the Chief State Sanitary Doctor of the USSR on December 27, 1973, must be observed.

7.7. Enterprises performing radiographic testing of welded joints develop, in accordance with the safety requirements of this section, documentation that defines the rules and methods for the safe organization of work, the scope and means of radiographic testing, taking into account local production conditions, and bring them to the workers in the prescribed manner.

8. Metrological support

8.1. The groove and plate sensitivity standards used in the control must be subjected to metrological verification upon their release and subsequent verification at least once every 5 years. When these standards are produced, on the reverse side of each standard, the trademark of the enterprise that produced the standard and the year of issue must be applied by electrochemical method; at the next verification - the trademark or symbol of the enterprise that carried out the verification, and the year of verification.

8.2. Wire standards of sensitivity are not subject to verification, however, they should be withdrawn from circulation in case of any damage to the plastic cover or if traces of corrosion of the wires of the standard are found during visual inspection.

8.3. Densitometers and sets of optical densities used to determine the optical density of images are subject to verification at least once a year with the obligatory execution of a document (certificate) on the verification results.

8.4. Negatoscopes are subject to verification only upon their release with the obligatory indication in the passport (certificate) of the negatoscope of the maximum brightness of the illuminated field and the optical density of the image.

8.5. Measuring tools used to determine the dimensions of the images of cracks, lack of penetration, pores and inclusions in the images (measuring rulers and magnifiers) are subjected to verification in accordance with the provisions in force that apply to these tools.

8.6. Non-standardized measuring instruments used to determine the dimensions of the images of cracks, lack of penetration, pores and inclusions in the images (measuring templates, stencils, etc.) must be verified at least once a year with the obligatory execution of a document on the verification results.

Sec. 8. (Introduced additionally, Rev. N 1).

Open the current version of the document right now or get full access to the GARANT system for 3 days for free!

If you are a user of the Internet version of the GARANT system, you can open this document right now or request it via the Hotline in the system.

The standard establishes a method for radiographic testing of welded joints made of metals and their alloys, made by fusion welding, with a thickness of welded elements from 1 to 400 mm, using x-ray, gamma and bremsstrahlung radiation and radiographic film.

CONTROL DESTRUCTIVE

CONNECTIONSWELDED

RADIOGRAPHIC METHOD

GOST 7512-82

STANDARDS PUBLISHING HOUSE

Moscow

STATE STANDARD OF THE UNION OF THE SSR

Introduction date 01.01.84

This standard establishes a method for radiographic testing of welded joints made of metals and their alloys, made by fusion welding, with a thickness of the welded elements from 1 to 400 mm, using x-ray, gamma and bremsstrahlung radiation and radiographic film.

1. GENERAL PROVISIONS

1.1. Radiographic control is used to detect cracks, lack of penetration, pores, slag, tungsten, oxide and other inclusions in welded joints.

1.2. Radiographic control is also used to detect burns, undercuts, assess the magnitude of the convexity and concavity of the root of the seam, which are unacceptable for external examination.

any discontinuities and inclusions with a size in the direction of transmission less than twice the sensitivity of the control;

lack of penetration and cracks, the opening plane of which does not coincide with the direction of translucence and (or) the size of the opening is less than the values \u200b\u200bgiven in;

any discontinuities and inclusions, if their images on the pictures coincide with the images of foreign parts, sharp corners or sharp changes in the cracks of the translucent metal.

1.1 - 1.3.

Table 1

Markings of sizes established by GOST 15843-79 should be used.

2.2. During radiographic control, radiographic films that meet the requirements of the technical specifications for them should be used.

The type of radiographic film should be established by the technical documentation for the control or acceptance of welded joints.

2.5. Screens must have a clean, smooth surface. The presence of wrinkles, scratches, cracks, tears and other defects on the screens is not allowed.

2.6. Film loading cassettes must be opaque and provide a tight hold of the intensifying screens to the film.

2.7. To protect the film from scattered radiation, it is recommended to shield the film cassette from the side opposite to the radiation source with lead screens.

The thickness of protective screens is given in .

1 - insert; 2 - cover.

Crap. one.

2.8. To determine the sensitivity of the control, wire, groove or plate sensitivity standards should be used.

2.9. Sensitivity standards should be made from a metal or alloy whose base chemical composition is similar to that of the welded joint being tested.

2.10. The shape and dimensions of the wire sensitivity standards are given on and in. The length of the wires in the standards is (20 ± 0.5) mm. Limit deviations for wire diameters:

up to 0.2 mm... + 0.01 mm

St. 0.2 to 1.6 mm... ± 0.03 mm

» 1.6 » 4.0 mm... ± 0.04 mm.

Table 2

2.12. The shape and dimensions of the plate sensitivity standards are given on and in.	Groove depth						Previous off groove depths	R , no more	a		b		c		h		L
h 1	h 2	h 3	h 4	h 5	h 6	Rated	Previous off groove depths	R , no more	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off
	0,60	0,5	0,40	0,3	0,20	0,10	0,05	0,1	2,5	±0.30; ±0.150	0,5	0,2; +0,1		0,360		0,100		0,52
	1,75	1,5	1,25	1,0	0,/5	0,50	0,10	0,2	4,0	±0.40	1,5	0,3		0,430		0,120		0,62
			3,00	2,5	2,00	1,50	0,25	0,3	6,0	±0.40	3,0	0,3		0,430		0,120		0,74
	4,00	3,5					0,30	0,3	6,0	±0.40	3,0	0,3		0,430		0,120		0,74

(Revised edition, Rev. No. 1).

Table 4

h		D		d		a		b		c		L
Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off
0,1	0,01	0,2	0,01	0,1	0,01		±0.15		±0.15		0,36		0,52
0,2	0,025	0,4	0,025	0,2	0,025
0,3		0,6		0,3
0,4		0,8		0,4
0,5		1,0		0,5
0,60	0,06	1,2	0,06	0,60	±0.06				±0.18		0,43		0,62
0,75		1,5		0,75
1,00		2,0		1,00
1,25		2,5		1,25
1,5	0,1	3,0	0,10	1,5	0,1		±0.18
2,0		4,0	0,12	2,0
2,5		5,0	0,12	2,5

Symbols for the material of the sensitivity standard: for alloys based on iron - 1, aluminum and magnesium - 2, titanium - 3, copper - 4, nickel - 5.

2.14. For marking groove standards, it is allowed to use cutouts and holes or only the holes specified in. In this case, the thickness of the standard at the place of marking should be equal to h.

When marking with standard holes, the length of standard No. 1 is 27 -0.52 mm, No. 2 - 38.5 -0.62 mm, No. 3 - 53 -0.74 mm.

2.15. For welded products intended for export, the use of other types of sensitivity standards is allowed, if it is provided for by the conditions of export.

3. PREPARATION FOR CONTROL

3.1. Radiographic inspection should be carried out after removing the external defects found during the external examination of the welded joint and cleaning it from bumps, slag, splashes of metal, scale and other contaminants, the images of which in the image may interfere with the interpretation of the image.

3.2. After stripping the welded joint and eliminating external defects, the welded joint should be marked into sections and marked (numbered) of the sections.

3.1, 3.2. (Changed edition, Rev. No. 1).

3.3. The system for marking and marking sections is established by technical documentation for the control or acceptance of welded joints.

3.4. During the control, sensitivity standards and markings should be installed at each section.

3.5. Sensitivity standards should be installed on the controlled area from the side facing the radiation source.

3.6. Wire standards should be installed directly on the seam with the direction of the wires across the seam.

3.7. Groove standards should be installed at a distance of at least 5 mm from the seam with the direction of the grooves across the seam.

3.8. Plate standards should be installed along the seam at a distance of at least 5 mm from it or directly on the seam with the direction of the standard across the seam so that the images of the markings of the standard do not overlap the image of the seam in the image.

3.9. When testing circumferential welds of pipelines with a diameter of less than 100 mm, it is allowed to install groove standards at a distance of at least 5 mm from the weld with the grooves directed along the weld.

3.11.(Deleted, Rev. No. 1).

3.12. Markings used to limit the length of sections of welded joints controlled in one exposure should be installed at the boundaries of the marked sections, as well as at the boundaries of the deposited and base metal when testing welded joints without reinforcement or with the weld reinforcement removed.

3.13. The markings used for numbering the controlled areas should be installed on the controlled area or directly on the film cassette so that the images of the marks on the images do not overlap the image of the seam and the near-seam zone along.

3.14. If it is impossible to install sensitivity standards and (or) markings on the inspected section of the welded joint in accordance with the requirements of this standard, the procedure for testing without installing sensitivity standards and (or) markings should be provided in the technical documentation for the control or acceptance of welded joints.

4. CONTROL SCHEMES

4.1. Welded joints should be controlled by and .

4.2. With a limited width of the element to be welded, it is allowed to inspect tee welded joints with the direction of radiation along the generatrix of this element in accordance with.

4.2a. When testing circumferential welded joints of cylindrical and spherical hollow products, as a rule, it is necessary to use schemes of transillumination through one wall of the product (diagrams in Fig. 5 a, b, e, and, h). In this case, it is recommended to use transmission schemes with the location of the radiation source inside the controlled product:

5.1, 5.2 (Revised edition, Rev. No. 1).

for butt and lap joints:

not less than 5 mm - with thick welded edges up to 5 mm;

not less than the thickness of the welded edges - with the thickness of the welded edges St. 5 to 20 mm;

not less than 20 mm - with a thickness of welded edges of St. 20 mm;

for tee and corner joints - is established by the technical documentation for the control or acceptance of these joints.

6. IMAGE INTERPRETATION

6.1. Viewing and interpretation of images should be carried out after they have completely dried in a darkened room using special illuminators-negatoscopes.

Negatoscopes with adjustable brightness and illuminated field size should be used. The maximum brightness of the illuminated field must be at least 10 D + 2 cd / m 2, where D- optical density of the image. The dimensions of the illuminated field should be adjusted using movable shutters or mask screens within such limits that the illuminated field is completely covered by the image.

(Changed edition, Rev. No. 1).

6.2. Photographs approved for decryption must meet the following requirements:

the pictures should not have spots, stripes, pollution and damage to the emulsion layer, making it difficult to decipher them;

images of limit marks, markings and sensitivity standards should be visible on the pictures;

the optical density of the images of the controlled section of the seam, the heat-affected zone and the sensitivity standard should be at least 1.5;

the decrease in the optical density of the image of the welded joint in any part of this image in comparison with the optical density of the image of the sensitivity standard should not exceed 1.0.

6.3. The sensitivity of the control (the smallest diameter of the wire standard detected in the image, the smallest depth of the groove standard detected in the image, the smallest thickness of the plate standard, at which a hole with a diameter equal to twice the thickness of the standard is detected in the image), should not exceed the values \u200b\u200bgiven in.

Table 6

Examples of abbreviated recording of defects when deciphering images are given in.

7. SAFETY REQUIREMENTS

7.1. The main hazards for personnel during radiographic control are exposure to organismizing radiation and harmful gases formed in the air under exposure to radiation, and electric shock.

7.2. Radiographic control and recharging of radioactive sources should be carried out only using equipment specially designed for these purposes and in good condition, the documentation for the manufacture and operation of which, when issued in more than three copies, must be agreed with the USSR State Committee for the Use of Atomic Energy and the Main Sanitary and Epidemiological Directorate of the USSR Ministry of Health ; up to three copies - with local bodies of the sanitary and epidemiological service.

Type of defect	Symbol		The nature of the defect	Symbol
Type of defect	Russian alphabet	Latin alphabet	The nature of the defect	Russian alphabet	Latin alphabet
cracks			Crack along the seam	TV
			Crack across the seam	Tp
			The crack is branched	Tr
lack of fusion			Failure at the root	Hk
			Lack of penetration between rollers	Hb
			Lack of cutting	HP
pores			Separate time
			Chain	CPU
			Cluster	joint venture
Slag inclusions			Separate inclusion
			Chain	TsSH
			Cluster	ssh
Tungsten inclusions			Separate inclusion
			Chain	CV
			Cluster	SW
oxide inclusions
Weld root concavity	Vgk
Convexity of the root of the seam	VPK
undercut	PDR
Edge offset	Skr

(Revised edition, Rev. No. 1).

2. For abbreviated recording of the maximum total length of defects (on a section of an image 100 mm long or on the entire image with its length less than 100 mm), the symbol E should be used.

3. After the conditional designation of defects, their dimensions are indicated in millimeters:

for spherical pores, slag and tungsten inclusions - diameter;

for elongated pores, slag and tungsten inclusions - width and length (through the multiplication sign);

for chains, accumulations, oxide inclusions, lack of fusion and cracks - length.

4. For chains and accumulations of pores, slag and tungsten inclusions, after the conditional designation of defects included in the chain or accumulation, the maximum diameter or width and length of these defects (through the multiplication sign) are indicated.

5. If there are images of identical defects in the image (of a defective type with the same dimensions), it is allowed not to record each of the defects separately, but to indicate their number before the symbol of the defects.

6. After the symbol of the maximum total length of defects (in the area of the image 100 mm long), this length is indicated in millimeters.

7. If there are no images of defects in the image, as well as in cases where the length, width and total length of defects do not exceed the specified maximum allowable values, in the “Meets the requirements” column of the documentation, “yes” is written, otherwise - “no”.

8. If defects are found in the image of the images that are not listed in, in the conclusion or in the log of registration of control results, the full name of the defects should be indicated.

APPENDIX 6

Reference

EXAMPLES OF ABBREVIATED RECORDING OF DEFECTS DURING INTERPRETATION OF IMAGES AND DOCUMENTATION OF THE RESULTS OF RADIOGRAPHIC CONTROL

1. The image shows images of five pores with a diameter of 3 mm each, a chain of pores with a length of 30 mm and a maximum length and width of pores in the chain of 5 and 3 mm, and a slag inclusion with a length of 15 mm and a width of 2 mm.

The maximum total length of defects in a 100 mm image section is 20 mm.

Documentation entry: 5P3; Ts30P5×3; W15×2;S 20.

2. Images of two accumulations of pores (the length of each accumulation is 10 mm, the maximum diameter of pores is 0.5 mm) and an accumulation of slag inclusions (the accumulation length is 8 mm, the maximum length and width of inclusions are 2 and 1 mm) were found on the image.

The maximum total length of defects in a 100 mm image section is 18 mm.

Documentation entry: 2S10P0.5; S8SH2×1;S 18.

3. Images of two lacks of fusion 15 mm long and each crack 40 mm long were found in the image.

Record documentation: 2H15; T40.

4. Images of five pores with a diameter of 4 mm, each with a lack of penetration 20 mm long, were found in the image.

The maximum total length of pores in a 100 mm image section is 12 mm.

Documentation entry: 5P4;S 12; H20.

INFORMATION DATA

1. DEVELOPERS

G. I. Nikolaev, B. A. Khripunov, Yu. I. Udralov, E. G. Volkovyskaya.

2. APPROVED AND INTRODUCED BY Decree of the USSR State Committee for Standards No. 4923 dated 20.12.82.

3. REPLACE GOST 7512-75.

4. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS.

5. The limitation of the validity period was removed by decision of the Interstate Council for Standardization, Metrology and Certification (IUS 5-6-93).

6. Reissue (December 1994) with Amendment No. 1 approved in March 1988 (IUS 6-88).

TESTING NON-DESTRUCTIVE

WELDED CONNECTIONS

RADIOGRAPHIC METHOD

GOST 7512-82

STANDARDS PUBLISHING HOUSE

Moscow

STATE STANDARD OF THE UNION OF THE SSR

Introduction date 01.01.84

1. GENERAL PROVISIONS

1.1. Radiographic control is used to detect cracks, lack of penetration, pores, slag, tungsten, oxide and other inclusions in welded joints.

1.2. Radiographic control is also used to detect burns, undercuts, assess the magnitude of the convexity and concavity of the root of the seam, which are unacceptable for external examination.

any discontinuities and inclusions with a size in the direction of transmission less than twice the sensitivity of the control;

lack of penetration and cracks, the opening plane of which does not coincide with the direction of translucence and (or) the opening value is less than the values \u200b\u200bgiven in;

any discontinuities and inclusions, if their images on the images coincide with images of foreign parts, sharp corners or sharp changes in cracks in the translucent metal.

1.1 - 1.3.

Table 1

Markings of sizes established by GOST 15843-79 should be used.

2.2. During radiographic control, radiographic films that meet the requirements of the technical specifications for them should be used.

The type of radiographic film must be established by the technical documentation for the control or acceptance of welded joints.

2.4. Metal and fluorescent screens should be used as intensifying screens for radiographic testing.

The type of intensifying screen must be established by the technical documentation for the control or acceptance of welded joints.

The thickness of metal intensifying screens and methods for loading film into cassettes using screens are given in.

2.5. Screens must have a clean, smooth surface. The presence of wrinkles, scratches, cracks, tears and other defects on the screens is not allowed.

2.6. Film loading cassettes must be opaque and provide a tight hold of the intensifying screens to the film.

2.7. To protect the film from scattered radiation, it is recommended to shield the film cassette from the side opposite to the radiation source with lead screens.

The thickness of the protective screens is given in.

1 - insert; 2 - cover.

Crap. one.

2.8. To determine the sensitivity of the control, wire, groove or plate sensitivity standards should be used.

2.9. Sensitivity standards should be made of a metal or alloy whose base is similar in chemical composition to the base of the welded joint being tested.

2.10. The shape and dimensions of the wire sensitivity standards are given on and in. The length of the wires in the standards is (20 ± 0.5) mm. Limit deviations for wire diameters:

up to 0.2 mm... + 0.01 mm

St. 0.2 to 1.6 mm... ± 0.03 mm

» 1.6 » 4.0 mm... ± 0.04 mm.

Table 2

2.12. The shape and dimensions of the plate sensitivity standards are given on and in.	Groove depth						Previous off groove depths	R, no more	a		b		c		h		L
h 1	h 2	h 3	h 4	h 5	h 6	Rated	Previous off groove depths	R, no more	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off
	0,60		0,40		0,20	0,10	0,05			±0.30; ±0.150		0,2; +0,1		0,360		0,100		0,52
	1,75		1,25		0,/5	0,50	0,10			±0.40				0,430		0,120		0,62
			3,00		2,00	1,50	0,25			±0.40				0,430		0,120		0,74
	4,00						0,30			±0.40				0,430		0,120		0,74

(Revised edition, Rev. No. 1).

Table 4

h		D		d		a		b		c		L
Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off	Rated	Previous off
	0,01		0,01		0,01		±0.15		±0.15		0,36		0,52
	0,025		0,025		0,025



0,60	0,06		0,06	0,60	±0.06				±0.18		0,43		0,62
0,75				0,75
1,00				1,00
1,25				1,25
			0,10				±0.18
			0,12
			0,12

Symbols for the material of the sensitivity standard: for alloys based on iron - 1, aluminum and magnesium - 2, titanium - 3, copper - 4, nickel - 5.

2.14. For marking groove standards, it is allowed to use cutouts and holes, or only the holes specified in. In this case, the thickness of the standard at the place of marking should be equal to h.

When marking standards with holes, the length of standard No. 1 is 27 -0.52 mm, No. 2 - 38.5 -0.62 mm, No. 3 - 53 -0.74 mm.

2.15. For welded products intended for export, it is allowed to use other types of sensitivity standards, if it is provided for by the export conditions.

3. PREPARATION FOR CONTROL

3.2. After stripping the welded joint and eliminating external defects, the welded joint should be marked into sections and marked (numbered) of the sections.

3.1, 3.2. (Changed edition, Rev. No. 1).

3.3. The system for marking and marking sections is established by technical documentation for the control or acceptance of welded joints.

3.4. During the control, sensitivity standards and markings should be installed at each site.

3.5. Sensitivity standards should be installed on the controlled area from the side facing the radiation source.

3.6. Wire standards should be installed directly on the seam with the direction of the wires across the seam.

3.7. Groove standards should be installed at a distance of at least 5 mm from the seam with the direction of the grooves across the seam.

3.11.(Deleted, Rev. No. 1).

3.13. The markings used for numbering the controlled areas should be installed on the controlled area or directly on the film cassette so that the images of the marks on the pictures do not overlap with the image of the seam and the heat-affected zone according to .

4. CONTROL SCHEMES

4.1. Welded joints should be controlled by and.

4.2. With a limited width of the element to be welded, it is allowed to inspect tee welded joints with the direction of radiation along the generatrix of this element in accordance with.

4.2a. When testing circumferential welded joints of cylindrical and spherical hollow products, as a rule, it is necessary to use schemes of transillumination through one wall of the product (diagrams of Fig. 5 a, b, e, and, h). In this case, it is recommended to use transmission schemes with the location of the radiation source inside the controlled product:

5.1, 5.2 (Revised edition, Rev. No. 1).

for butt and lap joints:

not less than 5 mm - with a thickness of welded edges up to 5 mm;

not less than the thickness of the edges to be welded - with the thickness of the edges to be welded St. 5 to 20 mm;

not less than 20 mm - with a thickness of welded edges of St. 20 mm;

for tee and corner joints - is established by the technical documentation for the control or acceptance of these joints.

6. IMAGE INTERPRETATION

6.1. Viewing and interpretation of images should be done after they have completely dried in a darkened room using special illuminators-negatoscopes.

Negatoscopes with adjustable brightness and illuminated field size should be used. The maximum brightness of the illuminated field should be at least 10 D + 2 cd / m 2, where D- optical density of the image. The dimensions of the illuminated field should be adjusted using movable shutters or mask screens within such limits that the illuminated field is completely covered by the image.

(Revised edition, Rev. No. 1).

6.2. Photographs approved for decoding must meet the following requirements:

the pictures should not have spots, stripes, pollution and damage to the emulsion layer, making it difficult to decipher them;

images of limit marks, markings and sensitivity standards should be visible on the pictures;

the optical density of the images of the controlled section of the weld, the near-weld zone and the sensitivity standard must be at least 1.5;

the decrease in the optical density of the image of the welded joint in any part of this image in comparison with the optical density of the image of the sensitivity standard should not exceed 1.0.

6.3. The sensitivity of the control (the smallest diameter of the wire standard wire detected in the picture, the smallest depth of the groove standard groove detected in the picture, the smallest thickness of the plate standard, at which a hole with a diameter equal to twice the thickness of the standard is detected in the picture), should not exceed the values \u200b\u200bgiven in.

Table 6

Examples of abbreviated recording of defects when deciphering images are given in.

7. SAFETY REQUIREMENTS

Type of defect	Symbol		The nature of the defect	Symbol
Type of defect	Russian alphabet	Latin alphabet	The nature of the defect	Russian alphabet	Latin alphabet
cracks			Crack along the seam	TV
			Crack across the seam	Tp
			The crack is branched	Tr
lack of fusion			Failure at the root	Hk
			Lack of penetration between rollers	Hb
			Lack of cutting	HP
pores			Separate time
			Chain	CPU
			Cluster	joint venture
Slag inclusions			Separate inclusion
			Chain	TsSH
			Cluster	ssh
Tungsten inclusions			Separate inclusion
			Chain	CV
			Cluster	SW
oxide inclusions
Weld root concavity	Vgk
Convexity of the root of the seam	VPK
undercut	PDR
Edge offset	Skr

(Revised edition, Rev. No. 1).

2. For abbreviated recording of the maximum total length of defects (on a section of an image 100 mm long or on the entire image if its length is less than 100 mm), the symbol E should be used.

3. After the conditional designation of defects, their dimensions are indicated in millimeters:

for spherical pores, slag and tungsten inclusions - diameter;

for elongated pores, slag and tungsten inclusions - width and length (through the multiplication sign);

for chains, accumulations, oxide inclusions, lack of fusion and cracks - length.

4. For chains and accumulations of pores, slag and tungsten inclusions, after the symbol for defects included in the chain or accumulation, the maximum diameter or width and length of these defects (through the multiplication sign) are indicated.

5. If there are identical defects in the image (defects of the same type with the same size), it is allowed not to record each of the defects separately, but to indicate their number before the defect symbol.

6. After the designation of the maximum total length of defects (in the area of the image 100 mm long), this length is indicated in millimeters.

7. If there are no images of defects in the image, as well as in cases where the length, width and total length of defects do not exceed the specified maximum allowable values, “Yes” is written in the documentation column “Meets the requirements”, otherwise - “no”.

8. If defects not listed in the image are found in the image, the full name of the defects should be indicated in the conclusion or log of control results.

APPENDIX 6

Reference

EXAMPLES OF REDUCED RECORDING OF DEFECTS WHEN INTERPRETATION OF IMAGES AND DOCUMENTATION OF THE RESULTS OF RADIOGRAPHIC CONTROL

The maximum total length of defects in a 100 mm image section is 20 mm.

Documentation entry: 5P3; Ts30P5×3; W15×2;S 20.

The maximum total length of defects in a 100 mm image section is 18 mm.

Documentation entry: 2S10P0.5; S8SH2×1;S 18.

3. Images of two lacks of penetration 15 mm long each and cracks 40 mm long were found in the image.

Record documentation: 2H15; T40.

4. Images of five pores with a diameter of 4 mm each and a lack of fusion 20 mm long were found in the image.

The maximum total pore length in a 100 mm image section is 12 mm.

Documentation entry: 5P4;S 12; H20.

INFORMATION DATA

1. DEVELOPERS

G. I. Nikolaev, B. A. Khripunov, Yu. I. Udralov, E. G. Volkovyskaya.

2. APPROVED AND INTRODUCED BY Decree of the USSR State Committee for Standards No. 4923 dated December 20, 1982.

3. REPLACE GOST 7512-75.

4. REFERENCE NORMATIVE AND TECHNICAL DOCUMENTS.

5. The validity period was removed by decision of the Interstate Council for Standardization, Metrology and Certification (IUS 5-6-93).

6. Reissue (December 1994) with Amendment No. 1 approved in March 1988 (IUS 6-88).

GOST 7512-82

UDC 621.791.053:620.179:006.354 Group B09

STATE STANDARD OF THE UNION OF THE SSR

TESTING NON-DESTRUCTIVE

WELDED CONNECTIONS

RADIOGRAPHIC METHOD

nondestructive testing. Welded joints. Radiography method

Introduction date 1984-01-01

INFORMATION DATA

1. PERFORMERS

G.I. Nikolaev, B.A. Khripunov, Yu.I. Udralov, E.G. Volkovysk

2. APPROVED AND INTRODUCED Decree of the USSR State Committee for Standards dated December 20, 1982 No. 4923

3. IN REPLACEMENT GOST 7512-75

4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS

5. The limitation of the validity period was removed by decision of the Interstate Council for Standardization, Metrology and Certification (IUS 5-6-93)

6. Reissue (December 1994) with Amendment No. 1 approved in March 1988 (IUS 6-88)

1. GENERAL PROVISIONS

1.1. Radiographic control is used to detect cracks, lack of penetration, pores, slag, tungsten, oxide and other inclusions in welded joints.

1.2. Radiographic control is also used to detect burns, undercuts, assess the magnitude of the convexity and concavity of the root of the seam, which are unacceptable for external examination.

1.3. Radiographic control does not reveal:

any discontinuities and inclusions with a size in the direction of transmission less than twice the sensitivity of the control;

lack of penetration and cracks, the opening plane of which does not coincide with the direction of translucence and (or) the opening value is less than the values \u200b\u200bgiven in table. one;

any discontinuities and inclusions, if their images on the images coincide with images of foreign parts, sharp corners or sharp changes in cracks in the translucent metal.

Table 1

1.1-1.3.

(Introduced additionally, Rev. No. 1).

2. REQUIREMENTS FOR CONTROL ACCESSORIES

2.1. For radiographic inspection, marks should be used that are made of a material that ensures that they are clearly visible on radiographic images.

Markings of sizes established by GOST 15843-79 should be used.

2.2. During radiographic control, radiographic films that meet the requirements of the technical specifications for them should be used.

The type of radiographic film must be established by the technical documentation for the control or acceptance of welded joints.

2.3. During radiographic control, radiation sources provided for by GOST 20426-82 should be used.