Decorative elements made of polystyrene foam for the facade. Decoration of arches from polyurethane Decorative finishing from polyurethane

Despite its ancient origin, decorative stucco molding and decor have not lost their relevance today. But if earlier wall decoration and ceilings with decorative elements were available to a limited circle of very wealthy people, today new technologies and materials have made stucco much cheaper. At the same time, without loss of quality - polyurethane stucco molding has not lost the conviviality, sophistication and sophistication of its ancient predecessors.

Stucco polyurethane decor: advantages and disadvantages

Today, stucco molding and polyurethane decor have become a worthy alternative to plaster products - it is stronger, does not crumble and does not turn yellow over time.

In addition, polyurethane stucco molding has a number of other advantages:

• light weight, which greatly simplifies the installation of stucco molding; it is fixed with “liquid nails” type glue
• It is resistant to moisture, so it can be installed in the bathroom, kitchen or hallway

• easy to maintain - polyurethane does not attract dust, it is easy to clean
• does not absorb or accumulate odors
• perfectly withstands significant temperature changes
• fungus or mold does not grow or multiply on it
• impact resistance – products made of polyurethane can withstand fairly large mechanical impacts
• Possibility of painting – the polyurethane surface can be painted with oil-based or water-soluble paints paints, nitro varnishes and nitro paints are contraindicated

Advice! To visually “age” polyurethane, you need acrylic paint beige shades, carefully walk along concave surfaces

In addition to the fact that polyurethane is flammable and is of synthetic origin, other disadvantages are largely caused by manufacturing errors, characteristic mainly of Chinese manufacturers. First of all, this is a visually distinguishable surface grain, as well as a “jumping” uneven pattern that can arise when joining products from different batches.

Polyurethane stucco in the interior: application possibilities

Molded decor made of polyurethane is the widest range of decorative details for the interior:

• cornices - their main purpose is to design the junction of walls and ceiling, but at the same time they can also be used to divide the wall into tiers. Cornices can be smooth (quite universal, they can be used in different stylistic solutions) and with a pattern (they require a balanced selection so that the pattern matches the main style of the room)

Advice! IN small rooms ceiling modern cornices it is necessary to paint the same color as the walls - this will soften the transition, the section will not be so obvious, but will be visually raised

• friezes are an ornamental composition enclosed in the plane of a ribbon. It allows you to give the walls sophistication, grace and lightness, diluting the overall monotony

• capitals and brackets are a rather complex type of decoration that looks like a support for other elements, but at the same time they are not able to withstand significant loads. They can also be used as stands for decorative porcelain, not heavy lamps or vases, and as an independent decorative element. Capitals and brackets are most in demand when decorating rooms in classic or antique style, baroque

• moldings– in addition to decorating the ceiling and walls of the room, they are used to mark boundaries; their installation helps to visually add volume to the room. In addition, they are used to mask joints different materials or framing inserts. Molding can be made in modern (without ornament) and classic (simple or ornate ornament) style

Advice! Moldings and cornices can be used to disguise electrical wiring that may be buried underneath them.

• pilasters - half or three-quarter columns, in general outline repeating classical columns, but without thickening the trunk, they allow you to create the visual illusion of a colonnade without cluttering up the space. Actively used for space zoning

• sockets - ceiling decorations that allow you to hide (disguise) fasteners chandeliers. In the design of rosettes on the ceiling, various types of ornaments are used (oriental, floral, etc.), they can have different shapes - round, oval, square, diamond-shaped

This variety will help you select and harmoniously fit decorative stucco elements into the interior of almost any style:

• ancient Roman - it can be used maximum amount decorative stucco elements: pilasters, cornices, columns and niches. Sockets can be mounted both on the ceiling and on the walls, where they will act as an artistic panel

• Gothic style - stucco is used in it quite restrainedly and in doses - this concerns both the number of elements used and their decorativeness. These are mainly consoles, columns (colonnades) of classical shape and caissons

• Renaissance - it is characterized by niches, various rosettes, cornices with ornaments, and caissons. Very often the ornaments are painted gray blue range
• Baroque is a haven for lovers of stucco, but characteristic feature style is the asymmetry of the elements. All elements used are volumetric; columns can be classic or twisted with a predominance of pilasters. In Baroque, stucco is often painted, resulting in various effects: abrasion, patination, gilding
• Rococo - stucco decoration has a pronounced antique character; the ornament includes helmets, spears and bows, as well as animals and vases. In the interior it is mainly used for framing doors, paintings, panels and mirrors

In recent years, polyurethane stucco has been widely used in interior decoration.

This fashion trend has spread due to the emergence of new technologies in the production of decorative elements.

For a long time it was believed that stucco molding was only appropriate in the interior of large rooms. Current practice convincingly proves that decorations of this type look great even in standard apartments.

Features of polyurethane

For an interior designer, polyurethane stucco molding makes it possible to create creative projects on any scale.

When a hall or façade is designed public building, can be used different kinds plaster moldings.

This is the most common material that has been used for many centuries and even millennia.

Gypsum is easy to process and durable to use. However, it has a serious drawback: the material quickly collapses under the influence of high humidity.

For this reason, gypsum products from antiquity have hardly survived to this day.

Stucco molding for interior decoration is made from polystyrene foam. Unlike gypsum, this material has high moisture resistance. Specific gravity minimal material.

At finishing works polystyrene foam products can be attached to walls or ceilings with simple PVA glue.

It is convenient to work with the material on surfaces that cannot be completely leveled. However, the appearance of polystyrene foam stucco leaves much to be desired.

The texture of the material is not expressive and turns yellow over time. To give decorative elements a decent look, they are painted. Products made from polyurethane do not have such disadvantages.

Interior finishing specialists emphasize that stucco elements made of polyurethane are more massive than polystyrene foam.

At the same time, the texture of the material is distinguished by classical nobility, like gypsum. Due to this property, facade stucco molding made of polyurethane is often used when decorating individual cottages.

Polyurethane is highly durable and completely insensitive to moisture. The material does not absorb odors and mold does not form on it.

Balusters and pedestals made of polyurethane can be washed without any fear of causing damage to them, which is not allowed to be done with plaster products.

Interior with stucco

Decorative finishing premises is carried out according to a certain algorithm. First of all, you need to create a design or design sketch.

It is difficult to make stucco molding from polyurethane with your own hands. Therefore, you need to choose the appropriate elements in a building materials store.

Most often the following decorations are used for decoration:

• decorative arches and rosettes;
• balusters and pilasters;
• borders and baseboards;
• pedestals and columns.

Sold here facade decor made of polyurethane. When finishing walls and ceilings with polyurethane stucco, unevenness is covered, electrical wiring and heating pipes.

Decoration of walls and ceilings

The interior of modern apartments and cottages necessarily contains lighting fixtures. Modern plasma TVs can be hung on the wall and even mounted on the ceiling.

When creating a sketch for the design of a room, the designer needs to take into account such features.

Polyurethane stucco molding is used with equal efficiency in any plane. To give the chandelier a more elegant look, a rosette is attached to the ceiling.

As a rule, it complements decorative tiles, with the help of which existing surface defects are hidden. Skirting boards laid at the junction of walls and ceilings give the room austerity and neatness.

You can visually expand the room and “raise” the ceiling using polyurethane stucco. To achieve this effect, the walls are separated by horizontal tiers.

Polyurethane cornices are used as dividers. When a modern flat screen TV is mounted on a wall, it can be “edged” with a polyurethane border.

The result of this technique will be original design walls. Using the play of color when painting walls, you can achieve an optical increase in volume.

Often, facade stucco molding made of polyurethane is used by designers for the same purpose.

Design of openings

Practice recent years shows that in the interior of large apartments it is possible to implement classic designs using polyurethane stucco molding.

There are no studio apartments in the layout interior doors. However, in the usual version, which is typical for cold climates, the doorways remain.

To create a cozy atmosphere in a living space, it is increasingly carried out decorative design window and door openings.

An excellent effect is achieved when using decorative polyurethane edging as a platband. If you combine a wide and narrow edging, you get an attractive-looking frame.

Polyurethane stucco molding is used for decoration various items, which are located in the interior. Flat TV has already been mentioned above.

An important subject in home environment is a mirror. A mirror is required in the hallway and bathroom.

If the apartment is sold design project, then the mirror never stays away. It can be framed in a rectangular frame or in the form of an arch.

The specific solution is determined general style interior Today, cottage owners are increasingly turning to the experience of antiquity. Russian Empire style and Roman classics in the interior are becoming commonplace.

Preparation for work and installation

When the owner of an apartment or private house saw interesting photo in a magazine and decided to decorate a similar picture in his interior, he should not rush.

According to traditions, as well as current norms and rules, any renovation in an apartment begins with planning.

Installation of polyurethane stucco molding is carried out without much difficulty. Anyone can do this job an adequate person, able to hold a hammer and drill.

In this situation, the most important link in the process is the creation of a sketch and the overall composition of the interior.

In times far from the present century, famous artists and architects were involved in the development of the project.

Once the sketch of the design of a specific room is ready, you can go to the store finishing materials and purchase polyurethane stucco molding.

Practice has convincingly proven that the production of such products for decoration in a handicraft way is unproductive. For this reason, it is easier and cheaper to buy interior and facade decor made from polyurethane in a store.

Simultaneously with the purchase of stucco molding, you need to take care of purchasing the tool. Many craftsmen already have most of the tools in their home.

It is important not to forget about the glue that will be needed to attach the elements to the walls and ceiling.

Decorative finishing with polyurethane stucco begins with simple action– you need to properly prepare the surface of walls and ceilings.

If required, the surfaces must be cleaned of deposits, puttied and coated with a primer. It is advisable to paint the ceilings and wallpaper the walls after completion of the work.

The next step is marking. This is an important stage, it must be done with high precision. On concrete surfaces The locations for drilling holes for fasteners are marked.

Symmetry is important in any interior, so when designing corner joints you need to ensure that this condition is met.

It is more convenient to attach polyurethane stucco molding to the ceiling using glue. Please note that the glue does not harden immediately. It takes several hours for it to reach condition.

At this time, the glued part must be additionally fixed. On concrete wall The stucco molding “sits” on the glue and is additionally fastened with self-tapping screws in the places designated in advance.

After the glue has hardened, the holes that appeared on the surface of the polyurethane are simply filled with putty. In this way, all quality requirements are met appearance.

For attaching polyurethane stucco molding to wooden surfaces you can use nails.

In practice, nails are used frequently. They are needed to prevent the elements from sliding off before the glue hardens, then they are pulled out.

To ensure that the interior maintains all the proportions laid out in the sketch, the stucco molding is painted in the appropriate color. It is important to note that acetone-based paint cannot be used.

Decorating a home with stucco has always been and is considered a sign of good taste and material wealth. An interior with stucco molding is still very relevant today: it allows you to create even a standard modern apartment unique and elegant style. Stucco molding is decorative elements repeating in the ornament, which come in different sizes and shapes. At first, stucco molding was made from gypsum, but now it is also made from polyurethane.

Features, advantages and disadvantages

Polyurethane stucco, unlike gypsum, has virtually no restrictions on its use. This decor is easy to install and does not require special adjustment.

Polyurethane stucco does not crumble and does not turn yellow over time, like gypsum. It also looks great in rooms with low ceilings.

Contrary to quite popular belief, polyurethane stucco is not a low-budget decor. High-quality polyurethane stucco molding is made by well-established manufacturing companies from steel molds coated with Teflon, which ensures dimensional accuracy and a clear pattern.

This stucco molding, unlike Chinese products, is very light, does not shrink or expand, is easy to install, and will not have cracks or gaps at the joints.

Advantages of polyurethane stucco molding

The undoubted advantages of such stucco molding include the following:

• environmental Safety;
• ease of installation;
• protection from mechanical damage;
• easy to care for (it is easy to wash, it does not attract dust and does not absorb odors).

Disadvantages of polyurethane stucco molding

It should be noted that there are existing negative properties of polyurethane stucco molding:

• fire instability;
• the buyer is limited in the choice of forms, since, unfortunately, such stucco molding is not produced for individual orders.

Methods of using stucco in the interior

In modern interior design, polyurethane stucco is used in a very diverse way. Here are some examples of its use:

1. Design of platbands and cornices.(with or without relief) they decorate the joints of walls and ceilings like cornices. At the same time, in small rooms, the cornices on the ceiling must be painted in the same tone as the walls, otherwise the ceiling will visually drop and the room will be “fragmented.”

   

   You can decorate the door or window opening with decorative polyurethane edging as a platband. Even arched openings (curved and complex) can be beautifully decorated.

   

   Double trims (wide and thin) look good; this way you get an impressive frame. It is especially stylish to use platbands as a continuous line - a solid one that borders windows, baseboards and doors at once.

   

2. Portal decor. A portal is a main entrance in architecture, most often U-shaped. IN home interior Doors, windows and fireplaces are decorated with portals. The use of polyurethane stucco molding will allow you to elegantly decorate the portals with garlands, capitals, cornices, pilasters and other interesting elements.



3. Creation of optical effects. And with the help of polyurethane stucco molding you can create an optical illusion. For example, a square within a rectangle or a square within a square. The result will be an extraordinary relief design of the walls, and by using different colors, you can achieve an optical expansion of the volume.



4. Design of columns and wall panels. Polyurethane stucco molding will allow you to effectively design columns and half-columns, while you can get beautiful architectural solutions from ordinary pillars. In addition, polyurethane wall structures are a more economical and easier to use substitute for MDF panels, and they look very impressive. They are used both in bedrooms and in hallways, kitchens and living rooms.



5. We design mirrors and more. Due to its moisture resistance, polyurethane stucco can also be used in bathrooms and kitchens. With the help of stucco the usual bathroom mirror turns into a beautifully designed element, which, moreover, can be coated “as gold.” A polyurethane lambrequin in the bedroom will advantageously hide.



6. Ceiling decoration. Polyurethane stucco molding can be used in all planes and on all surfaces, with the exception of the floor. Ceiling stucco is beautifully decorated with wide ceilings and rosettes for chandeliers. Rosettes give a more elegant look. Ceiling tiles are also used. With their help, you can beat large differences in load-bearing slabs.



Tools and materials

In order to start working with polyurethane stucco elements, you need to have:

• saw or hacksaw with fine teeth;
• miter box (sawing box);
• roulette;
• glue gun;
• stapler;
• spatula - apply glue;
• fine-grained emery cloth to remove hardened excess glue;
• glue for attaching elements to the ceiling and walls;
• glue for connecting parts together;
• finishing nails;
• hammer drill and self-tapping screws (for concrete walls).

Useful. Read - with or without a special device.

Installation of polyurethane stucco products

Before starting work:

• stucco products must be kept for at least 24 hours in the room where they will be installed (for adaptation);
• the glue should also be stored in a warm room;
• the ceiling and walls must be primed with a special compound for deep penetration, be clean, level and dry;
• It is necessary to glue wallpaper, paint walls and ceilings after installing stucco products.

Molding installation process:

1. The height of the profile is determined and markings are made on the wall.
2. The cut points for connecting the corners using a miter box are marked, and cuts are made for the corner joints according to the mark.



3. You need to go over the places where the glue will be applied with fine sandpaper.
4. Assembly adhesive is applied and evenly distributed along the entire length of the element from its reverse side.
5. The element is applied to the wall and glued with light pressure. To prevent it from slipping, you can drive small finishing nails under it - temporarily.



6. Excess glue is removed with a spatula.
7. The next element is applied, the joints are sealed with joint adhesive. The joint itself can be secured with staples using a stapler. Glue for joining must be applied in excess; its excess is then removed using a sponge soaked in acetone.



8. When the joint adhesive is completely dry (no earlier than a day), the nails and staples are removed. Excess glue is removed with a knife and emery cloth.
9. The joint is puttied with finishing putty and then sanded with fine sandpaper.

Greetings, my dear readers!

Decorative stucco molding was used in the interior and exterior of houses back in ancient times, however, has not lost its relevance even now. Previously, such decorations were available only to a limited number of rich people, but today new materials and technologies have made stucco much more accessible. So, polyurethane decor for walls, ceilings and floors is now popular.

At the same time, it believably imitates wood and plaster without loss of quality - plastic stucco molding that looks festive and elegant. Just like ancient and medieval predecessors.

100 thousand ideas for decorating premises with polyurethane stucco molding

At the moment, stucco, like many centuries ago, is the optimal solution for recreating the original and aesthetic interior. Of course, taking into account the use of modern technologies.

Decorative stucco elements are now no longer associated only with the luxury of bygone centuries. They have become a modern means of decorating premises. Application of decorations

Stucco molding is a continuation of the architecture of the home, and not just its decor. It can not just decorate, but completely transform the aesthetics of a room.

At the same time, it is capable of hiding communications (risers, pipes, etc.) passing in prominent places. Stucco molding can also decorate and play up the shortcomings of the room, for example, niches.

Based on the architectural and design solutions of the home, the decorative background, recreated using polyurethane decorations, can be worked out in different styles.

Usually, when thinking about stucco, we mean such decorative elements as cornices, friezes and moldings, baseboards, pilasters and columns, rosettes, patterned overlays for furniture, etc.

1. At the same time, polyurethane jewelry does not have to be traditionally white. Their finishing makes it possible to create a variety of aesthetic effects.
2. Thus, applying paint makes the elements pearlescent.
3. Treatment with patina and wax “aging” the jewelry and visually giving it a velvety feel.
4. This solution stands out in giving individuality to the design, such as gilding and silvering of decorative elements. Then the room will acquire the classic atmosphere of the past - aristocratic chambers of the 17th–19th centuries. Then the jewelry should be treated with gold leaf or painted with special acrylic paint.

The traditional material for creating stucco is building gypsum. However, in addition to some advantages, it also has obvious disadvantages. Gypsum is hygroscopic, which is why it is extremely undesirable to use it in wet areas. It has a large mass, is fragile, difficult to install and has a high cost.

Polyurethane does not have all these disadvantages. The appearance of decorative elements from it revived interest in stucco as an effective method of decorating an interior. Polyurethane jewelry quickly gained popularity due to its main advantages: durability, environmental friendliness, simplicity and ease of installation, light weight, and relatively inexpensive cost.

The widest selection of polyurethane stucco moldings includes the following products:

• corner elements;
• cornices, friezes, moldings, baguette, plinths;
• ceiling and wall sockets;
• various applied patterns and ornaments;
• pilasters, semi-columns and columns, bases and crowns for them, etc.

Comparison of gypsum and polyurethane stucco

In the photo: plaster decor at the top, polyurethane at the bottom, it is clear that the quality of the second is much higher.

High technical, operational and aesthetic characteristics have made polyurethane decor a worthy choice that can replace traditional plaster stucco.

1. If we talk about cost, then polyurethane decorations are cheaper than gypsum analogues. However, it cannot be said that their price is so inexpensive.
2. It is very difficult to visually distinguish decor made from polyurethane from stucco molding made from traditional plaster or alabaster. The polymer material can perfectly imitate them, as well as carved wood.
3. At the same time, jewelry made from weighs much less. This makes it easier to install them.
4. Polyurethane does not yellow and is much more durable than plaster decorations.
5. Plastic decor, in addition to its aesthetic appearance, also has a high degree of functionality. Thus, it can be used to mask surface defects, utility lines, hidden type lighting, ugly designs.

Polyurethane jewelry is made by extruding from molten plastic granules. Installation necessary elements is carried out by gluing them onto clean and dry substrates.

Decorative elements made of polyurethane: features, disadvantages and advantages

Thanks to technical specifications and features, polyurethane decor is a worthy competitor to analogues made from other building materials. Besides, plastic decorations have their own advantages:

• Small mass of elements. This simplifies and facilitates the installation of stucco. It is fixed with construction adhesive such as “liquid nails”
• The decor does not turn yellow or crumble over time
• Polyurethane is resistant to moisture, so products made from it can be installed in the kitchen, bathroom, and hallway.
• Caring for the decor is easy. Plastic is antistatic and does not attract dust, it is easy to clean, does not accumulate or absorb odors.

• It tolerates significant temperature changes well and is resistant to heating up to +280 degrees. Therefore it can be used near heating devices and lamps.
• Mold and other harmful microorganisms do not appear or multiply on the material.
• Polyurethane jewelry is impact-resistant and can withstand relatively large physical and mechanical loads.
• Plastic surfaces can be painted with water-soluble paints, as well as oil compositions. However, plastic is not resistant to nitro paints and nitro varnishes.

• Such decorations have a large selection of textures, textures and colors.

The disadvantages include the following.

1. The material has an average degree of flammability.
2. It is of synthetic origin.
3. Other shortcomings, or rather product defects, are caused by manufacturing errors, which are typical for low-quality, usually Chinese, analogues. First of all, this is the visually visible grain of their surface; in addition, there is an uneven (jumping) pattern that appears when matching jewelry from different batches.

500 possibilities of use

Polyurethane products for the interior are presented in a wide range. I have summarized for you the main types of such decor for the interior and facade of the house in a separate table.

Style solutions

The variety of elements described above will help you decorate your home in the interior of almost any room. You can use decor in these directions.

1. Ancient Roman, ancient Egyptian and ancient Greek styles, united in the antique direction. In its aesthetics, you can use a maximum of decorative elements made of polyurethane: columns, pilasters, capitals, brackets, frames of arches and niches, cornices. Sockets can be fixed to walls and ceilings. There they will be an element in the composition of the artistic panel.
2. Gothic direction. Stucco molding is used in doses and with restraint. This state of affairs also applies to the design of elements and their number. As a rule, these are colonnades or individual columns of classical orders, caissons and consoles.
3. Renaissance or Renaissance style. It is characterized by the use in design of niches, various rosettes, cornices decorated with ornaments, and caissons. Often the decor is painted in a gray-blue tone.

1. Baroque. Here I recommend that you do not limit your imagination and use as much stucco as possible.

That a strict feature of the direction is the asymmetry of the compositions of the elements. All types of decor used must be voluminous. Columns should be twisted or classic, always with predominant pilasters. In the Baroque style, the decor is often painted to obtain the effects of patination, gilding, and abrasions.

1. Rococo. Here the decorative elements have a pronounced imprint of antiquity. The design of the elements contains ornate, lush and complex patterns, animals, plants, vases, as well as bows, spears, and helmets. In interior design, polyurethane decorations are used to frame paintings, doors, wall panels, ceiling compositions and mirrors.

1. Empire and classic. These styles are quite restrained, but majestic and pathetic. There is a lot of decor, however, it is light, symmetrical, not massive and is designed to show imperial grandeur. The design of the elements is dominated by simple patterns and ornaments (geometric, floral) and shapes.
2. Aesthetics modern trends– loft, hi-tech, minimalism, often postmodernism excludes pretentiousness and pomp of decor.

The use of polyurethane stucco in a modern interior is limited by the dimensions of the room. In the room small size its abundance will visually reduce the space, causing a feeling of clutter. It is advisable to install ceiling elements only when the height of the walls is 3 m or more.

In interior design, polyurethane decorations can be used with your own hands to create a variety of visual illusions.

1. Thus, the decorative composition of a square within a square or a square within a rectangle recreates the unusual relief of the walls. If you choose the right colors here, you can achieve the optical effect of expanding the space.

1. Polyurethane stucco molding can be used to install portals framing doors, windows, arches, niches, and fireplaces. A variety of decorative elements will give you the opportunity to recreate portals, beautifully decorated with capitals, cornices, pilasters, garlands, etc.
2. Due to the water resistance of polyurethane decorations, an ordinary mirror in bathroom can be transformed in such a way that it becomes the dominant accent in the design of the room.
3. You can use cornice and molding to hide electrical wiring. It is easy to lay it under these slats.

1. The best option in a small room with modern ceiling cornices is to paint them the same color as the walls. This way you will soften the transition, the distinction will not be “conspicuous”, and the ceiling will be optically higher.
2. If you want to visually age a polyurethane decoration, carefully treat it with acrylic dye beige colour its concave surfaces.
3. Using a plastic lambrequin you can disguise a curtain rod.

The best manufacturers

My instructions conclude with a short review of the best manufacturers of polyurethane jewelry.

1. Orac Decor is the most famous Belgian manufacturer of elite polyurethane stucco moldings on the world market. Its products are elegant, stylish and sophisticated. The Orac Decor product range is diverse.
   Due to the highest quality, the decor of this company is very popular among users all over the world. Of course, this is also reflected in the cost of the products - they are far from cheap.

1. Gaudi Decor is a manufacturer from Malaysia. His decorative polyurethane products were among the first to appear on our market. They have best ratio in terms of quality/cost. Currently, Gaudi Decor's assortment includes about 850 jewelry, this is the highest figure among all manufacturers.
2. NMK (NMC) is a manufacturer of polyurethane stucco from Belgium. Decorative items The companies are of very high quality. Classic collections of profiles with designs inspired by plaster stucco molding will turn an ordinary room into a stately apartment.
   With visual similarity to heavy and expensive plaster stucco, the polymer decor of this company weighs very little, is easy to install and is not that expensive. The material does not contain toxic substances.

1. Solid is a wide selection of high-quality polyurethane decor from China. The products are intended for a wide range of users who want to change the monotony of typical homes.
   The brand has almost its own analogue on the construction market - the Harmony brand. Although such decorative elements are produced under different names, however, all these products are produced by the same Chinese factory. Solid is positioned as economy-class decor, so its cost is much lower than its European counterparts.
2. Perfect is a brand with wide range polyurethane jewelry, also originally from China. Almost a complete clone of Solid products. Despite this, the products have a good price/quality ratio. This stucco molding will be a good choice for a wide range of users.

1. Brand Harmony appeared on Russian market only in 2007. However, it has already become very popular. The range of products is varied, the quality is good, and the cost is very cheap - one of the lowest.
   Harmony collections are famous for their original design solutions. Decor made from polyurethane of this brand is subject to double quality control - first directly at the manufacturer’s factory, then at its warehouses. Thanks to this, the products are of good quality.

1. Polyurethane stucco molding Europlast is manufactured here in Russia. Due to the fact that the company has several branches in the regions of the country, products can be purchased almost everywhere. However, the most popular collections are not always in stock.
   The company produces all friezes, moldings and cornices in both rigid and flexible versions. Europlast is the only Russian manufacturer that can compete with foreign manufacturers of polyurethane decor.

Conclusion

Decorative elements made of polyurethane are an excellent alternative to classic plaster stucco. With their help, you can decorate your home in any of the selected design styles.

Of course, you might still have questions, ask them in the comments. If you watch the video in this article, you can visually study the topic.

So I say goodbye, and good luck to you in your endeavors!

Every owner treats with particular scrupulousness. If the main thing in capital structures is durability, functionality, and reliability, then this is about taste and often prosperity. The given characteristic corresponds as closely as possible to polyurethane stucco. The editors of the online magazine will help you understand the issue of choosing, operating and installing such interior decoration.

Stucco molding is far from a new interior element. They were decorated with it back in medieval and royal times. Then it was also considered an item of luxury and wealth. Classic material her execution had a composition reminiscent of modern plaster.

Today, decorating a home made of polyurethane is much more convenient and practical than its gypsum ancestor. It is easier to install and does not require adjustment. It is not characterized by yellowing and shedding under the influence of time. In addition, modern stucco has many more advantages:

1. Environmental friendliness of the material.
2. Resistance to mechanical damage.
3. Unpretentiousness and ease of care. Polyurethane does not attract dust and can be washed.

There are also disadvantages:

1. The material is not fire resistant.
2. Stucco molding is not produced under individual order, so the buyer's choice is limited to the available assortment.

Types of polyurethane stucco molding

The appearance of the product reflects the architectural style in which it is made or the symbolism displayed:

• plants of a wide variety of shapes and inflorescences;
• military paraphernalia;
• geometric shapes;
• space objects.

A separate type includes bas-reliefs that spew out whole sculptures, made with a small volume. Usually this is an original work that literally costs a fortune. However, savvy manufacturers have learned to create simple figures on a production scale.

Polyurethane stucco molding for the facade of the house

Molded cornices have become widespread in modern construction. With their help, they visually separate the floors of the house or perform them as an addition to.

It also performs an extremely useful function of secrecy. Sometimes it simply serves as decoration for arches. Such products are called moldings.

Composition and performance characteristics of polyurethane stucco molding

The required components of the main material of the product include:

• fiberglass;
• foamed polyurethane;
• polystyrene;
• glass composite

All these substances are combined under special conditions and the output is a material with amazing characteristics. Some manufacturers add other ingredients, keeping them a closely guarded secret. As an addition and to impart certain properties, stucco molding is sometimes laminated. It can only be installed indoors and painted with paints that are not chemically active. The opposite option is primed. More durable, therefore it is also used for exterior decoration. She is unpretentious in coloring methods.

Most consumers consider stucco molding a cheap way of decoration and do not pay attention to it either in information sources or in stores. But this statement is partly true for a Chinese-made product. High-quality ornaments are produced under the strict control of high-class specialists for the precise implementation of technology, which involves the use of steel forms with Teflon coating. This is the only way to achieve maximum accuracy and dimension of the design. Reputable manufacturers produce only high quality stucco moldings that correspond to the price category.

Manufacturers of polyurethane stucco moldings

From the selfish point of view of the consumer, only companies that have long and confidently occupied leading roles in the market can be considered reliable manufacturers of a complex product. This position can only be achieved through a responsible attitude towards their business. It manifests itself in careful adherence to complex technologies, quality control of raw materials and finished material, special attitude towards pre-sale preparation. It consists in the final processing of surfaces and bringing the geometry of elements to the highest accuracy, which ensures ease of joining, painting and other related processes.

Europlast is a reliable Russian manufacturer of polyurethane stucco moldings

Among domestic enterprises, we can highlight Europlast. It is distinguished by a powerful production base and a large staff of employees of various profiles who design stucco moldings that meet the latest requirements of technology and design. Europlast climbed to a fairly high position in the polyurethane decor market in just twenty years, starting with manufacturing.

Europlast regularly expands its collection by introducing new products into production. First of all, the concern focuses on the needs of the Russian buyer. The production of high-quality stucco patterns is not the only, but one of the main activities of the company. The list of products includes elements of hard decor and parts for car interiors. Moreover, the customer for the last type of product is very specific - the Volkswagen assembly plant in Kaluga. The company's representative offices are scattered throughout Russia. There are offices and warehouses in Kazakhstan, Belarus and Ukraine.

Popular foreign manufacturers of polyurethane stucco decoration

Of the industries whose product occupies a significant share in general offer, by ear:

• Chinese company "Perfect" . Offers the optimal combination of “price and quality”;
• "Orac Decor" And "NMC" . Representatives of Belgium, a country famous for its decor of the highest quality. Stucco has been produced for several decades. Many collections belong to the expensive and exclusive segment;
• "Fabolo Decor" . A Malaysian developer who located his production in Ukraine. There was no other opportunity to make products accessible to the wallets of Russian buyers - high quality indicators oblige us to keep prices at the appropriate level.

The first and most important thing to pay attention to when choosing is the country and manufacturer. Regardless of market position and “feedback from grateful customers,” Asian enterprises should be given last priority. No matter what, there is a high risk of running into a difference geometric dimensions elements, difficulty in performing docking. It is not always possible to predict how the decor will behave after a certain service life. Also be sure to pay attention to the clarity of retyping all elements decorative ornaments. As a rule, all these parameters are top level from European and domestic manufacturers.

Self-installation of polyurethane stucco molding

In order to secure the ornament yourself, you must have the bare minimum set of basic elements:

• adhesives - depending on the recommendations of the manufacturer and seller;
• – usually required for linear products;
• measuring devices - tape measure, level, miter box;
• , drill. You may have to drill holes.

Attention! Preliminary calculation of linear material requires taking into account losses when cutting corners. A minimum of 10 centimeters for each corner, not counting other difficulties and geometric features of the room.

Illustration	Description of action
	Installation is carried out only on dry, clean surfaces, preferably on the ceiling. But they are also carried out after the work is completed. After preparing the surface, measurements are taken and marks are made where the future stucco molding will be located.
	To avoid mistakes during direct installation, it is best to make markings on an unnecessary section or other flat surface. This especially applies to stucco moldings consisting of various elements.
	After which the molding, in accordance with the manufacturer’s recommendation, is wetted (or not) in water. Next, apply a little around the entire perimeter.
	In accordance with the markings, glue the elements to the surface. If there is excess glue, remove it immediately with a damp cloth.

Further work should be carried out only after the glue has completely set, the time of which is indicated on the packaging. The little details and details of installation depend on many factors, so you should follow the advice and recommendations of the manufacturer, who is more familiar than anyone else with the features and vagaries of their products.

Painting elements made of polyurethane stucco

Wall and ceiling stucco molding made of polyurethane looks more interesting in some interiors if you use it in a suitable way. Let's consider how to paint such decorative elements using patination technology.

Illustration	Description of action
	We glue the selected stucco molding and wait until the glue dries completely. We prime it and cover with masking tape those elements that you do not plan to paint.
	Coloring acrylic paints stucco and as soon as possible before it begins to dry out.
	Since we have a technology for creating patina, before the paint has set, we take a soft, damp cloth and wipe it in the right places. Noticed any missing areas? We tint and wipe again to the desired condition.
	Using the same technology, we continue staining with rubbing. Please note that the paint is removed each time with a clean rag.
	To make the stucco look as natural as possible, we paint the main elements in several layers using soaking movements. Depending on the location of the elements, it is not necessary to do this over the entire surface. Here, as they say, it's a matter of taste.
	Using a thin brush, apply the veins in a chaotic manner.
	If necessary, paint the protruding stucco elements with a light color using a dry brush, barely touching the surface of the product.
	We remove the tape and admire the polyurethane stucco molding, artificially aged with our own hands.

Please note that this type of painting is suitable for both polyurethane and gypsum products. Here the question lies more in the level of skill of the artist than in the type of material of the product.

Options for using polyurethane stucco with photos of facades and interiors

And now a little aesthetics. Let us fully enjoy the beauty and luxury of stucco in its different variations.

Facade stucco molding made of polyurethane with photos of the outside of buildings

For lovers of the classics, there are a lot of models of stucco moldings in the façade of the building, made in this style - beautiful curls, graceful bas-reliefs.

1 of 6

You can also choose universal options that can decorate any building facade. These stucco moldings include simple skirting boards, fillets and other molded decorative products.

Polyurethane stucco molding for walls and ceilings with photos of interiors

Interior stucco moldings look no less interesting than façade ones. It’s just that the latter “live” a little less than their “domestic counterparts”, since they are exploited in more harsh conditions. As you can see, stucco is a universal interior decoration. Do you want luxury or Renaissance, the severity of timeless classics, notes